The short answer
If your Homecrest home is switching from oil to gas, getting a new heating appliance, or has a cracked or deteriorating clay flue, you likely need a new chimney liner. We inspect the chimney first, then install a liner sized to the appliance it serves so exhaust vents safely and the masonry is protected.
A chimney liner is the channel inside your chimney that carries smoke and exhaust gases up and out of the house while shielding the surrounding brick and wood from heat and corrosion. Homecrest has rowhouses, detached homes and pre-war apartment buildings, and many of their chimneys are older masonry. Their flues were often built for oil or coal, not for the gas boilers and water heaters many homes use now. EliteSweep Chimney Services installs new liners for Homecrest homeowners and building owners, working from our office in Madison, about 2 miles away.
Why Homecrest Chimneys Often Need a New Liner
Many chimneys in older Brooklyn homes have clay tile liners or no liner at all. Over decades, clay tiles can crack from heat, mortar joints between them can wash out, and moisture can work its way into the brick. A damaged liner lets heat and exhaust reach places they shouldn't, including the inside of your walls.
Fuel conversions are another common reason. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of that work. A new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue from the inside. If your Homecrest home or building is planning a conversion, it makes sense to plan the liner at the same time.
Signs Your Liner May Need Attention
Some liner problems are only visible with a camera, but there are warning signs you can watch for at home:
- Pieces of clay tile or crumbled mortar at the base of the chimney or in the cleanout
- Water stains, peeling paint or damp spots on walls near the chimney
- White staining or flaking on the outside brick
- A strong odor from the fireplace or boiler area, especially in humid weather
- Your boiler, furnace or water heater has been replaced or switched to a different fuel
- An inspector or contractor has flagged the flue during a home sale or renovation
Choosing the Right Liner for Your Home
The right liner depends on what the chimney serves. A gas boiler, an oil furnace, a water heater and a wood-burning fireplace each have different needs for size, material and heat tolerance. Stainless steel liners are a common choice for many Brooklyn homes because they handle the acidic condensate from gas appliances well and can be fitted into existing masonry chimneys. Some chimneys with several appliances may need more than one flue.
Sizing matters as much as material. A liner that is too large can let exhaust cool and condense before it leaves the chimney, and one that is too small can restrict draft. We match the liner to the appliance so it vents properly. In multi-family and pre-war apartment buildings, we also look at how the boiler room, roof access and chimney layout affect the installation.
How Liner Installation Works
Every liner job starts with an inspection. When a system changes, such as a new appliance or a switch of fuel, or when a home is sold, chimney professionals use a Level 2 inspection, which typically includes a camera look inside the flue. If a hidden hazard has to be reached by opening part of the chimney or building, a Level 3 inspection is used. Our certified technicians then follow these general steps:
- Inspect the chimney and record the condition of the existing flue
- Clean the flue and remove loose debris or broken tile where needed
- Measure the flue and confirm the liner size for the appliance it serves
- Install the liner from the top down and connect it to the appliance
- Fit the top plate and cap, then check that the system drafts correctly
Timing Liner Work Around Heat Season
New York City's heat season runs from October 1 through May 31. During those months, building owners must keep apartments heated to the city's minimum temperatures, so a boiler that is down for chimney work can be a real problem. For Homecrest building owners, the warmer months are usually the easiest time to schedule a conversion or liner installation.
After the liner is in, keep up with yearly inspections. The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year, which helps catch problems early. We also serve nearby Gravesend, Madison, Midwood, Mapleton and Sheepshead Bay.
More services in Homecrest
- Chimney Sweep in HomecrestLocal service & repairs
- Chimney Inspection in HomecrestLocal service & repairs
- Chimney Repair in HomecrestLocal service & repairs
- Air Duct Cleaning in HomecrestLocal service & repairs
