Skip to content
Brooklyn, NY Brooklyn, NY Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (929) 531-5990

Chimney Liner Installation in Mill Basin, Brooklyn

Serving Mill Basin and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (929) 531-5990

The short answer

If your Mill Basin chimney has a cracked, corroded or missing liner, or you're switching your boiler from oil to gas, a new liner sized to your appliances keeps exhaust safely contained. EliteSweep inspects the flue, recommends the right liner type, and installs it from the roof down.

A chimney liner is the protective channel inside your flue. It carries smoke and exhaust out of the house and keeps heat and corrosive byproducts away from the surrounding brick and framing. Many Mill Basin homes are detached and semi-detached houses with masonry chimneys serving boilers, water heaters and fireplaces. When the liner in one of these chimneys cracks, corrodes or no longer suits the appliance connected to it, exhaust can leak into the home or damage the chimney from the inside. EliteSweep's certified technicians install new chimney liners for homes in ZIP code 11234, about a mile east of our office in Madison, Brooklyn.

Signs your Mill Basin chimney needs a new liner

Liner damage usually happens out of sight, so most homeowners learn about it during an inspection rather than by noticing it themselves. Older masonry chimneys may have clay tile liners with cracked or missing sections, and some chimneys were built with no liner at all. Signs worth having checked include:

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year. That yearly check is often where liner problems first show up, before they turn into a heating shutdown or a larger masonry repair.

  • Flakes of tile, mortar or rust collecting at the base of the flue or in the cleanout
  • White staining, damp spots or crumbling brick on the chimney, inside or out
  • A smoke or exhaust smell indoors when the fireplace, boiler or water heater is running
  • A new heating appliance or a fuel switch connected to an old flue
  • A past chimney fire, even a small one, which can crack tile liners

Oil-to-gas conversions and your flue

When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work. A new liner is often needed because gas exhaust produces acidic condensate that can corrode a masonry flue originally built to handle oil.

If your home is converting, or already converted and the chimney was never looked at, we can evaluate the flue and tell you plainly whether the existing liner is suitable. We work alongside your heating contractor so the liner is sized for the new boiler and any water heater sharing the chimney.

Matching the liner to your appliance and chimney

No single liner fits every chimney. The right choice depends on what vents into the flue, the size and shape of the existing chimney, and how many appliances share it. The main options are:

Sizing matters as much as material. A liner that is too large for a smaller modern boiler can let exhaust cool too quickly, which leads to condensation inside the flue. One that is too small can restrict draft and push exhaust back toward the appliance. We size each liner to the equipment actually connected to it.

  • Stainless steel liners, used for gas and oil appliances and wood-burning fireplaces, in flexible or rigid form to suit straight or offset flues
  • Cast-in-place liners, a mortar-like material poured around a form inside the chimney, which can also help strengthen older, deteriorated masonry
  • Clay tile replacement, possible in some chimneys, though it usually involves more demolition

What liner installation looks like

Every liner job starts with an inspection. Under NFPA 211, a Level 2 inspection applies when the system changes, such as a new appliance or a switch of fuel, so that is usually the starting point. If a hidden hazard has to be reached by opening part of the chimney or building, a Level 3 inspection may be needed. From there, the work typically follows these steps:

Most of the work happens on the roof and at the appliance connection, and we protect the floor where we work indoors. Before we leave, we explain what we found and what we installed.

  • Inspect the flue, often with a camera, and measure its size and height
  • Clean the chimney so the new liner goes into a clear flue
  • Remove broken tile or obstructions where needed
  • Lower the liner from the top and connect it to the appliance at the base
  • Add insulation where the liner type calls for it, plus a top plate and cap
  • Check draft and venting with the appliance running

Planning around New York City's heat season

New York City's heat season runs from October 1 through May 31, when building owners must keep apartments heated to the city's minimum temperatures. A liner problem found in the middle of winter can mean shutting down the boiler that heats your home, so late spring and summer are the easiest times to schedule liner work. If you rent out part of your house, a properly venting heating system is part of keeping tenants warm through the season.

Besides Mill Basin, we install chimney liners in nearby Marine Park, Bergen Beach, Flatlands, Madison and Sheepshead Bay.

More services in Mill Basin

Related

What to expect

How a visit goes

  1. We look before we recommend

    We inspect the flue, damper, crown, cap and connections first, then tell you what we found. Recommendations come from what is in your chimney, not from a standard package.

  2. We keep your home clean

    Drop cloths go down before any work starts, and soot and debris are contained and carried out. We leave the room the way we found it.

  3. We explain it in plain English

    You will hear what each problem is, why it matters, and what happens if you wait. If something can safely be left for later, we say so.

FAQ

Common questions

Don’t see your question? Call (929) 531-5990 and we’ll talk it through.

My chimney has never had a liner. Do I need one?

An unlined masonry chimney lets heat and exhaust reach the brick and nearby framing directly. An inspection will show whether your chimney has a liner and whether it suits the appliances connected to it.

Do I need a new liner when switching from oil to gas?

Often, yes. In New York City the chimney must be evaluated during an oil-to-gas boiler conversion, and gas exhaust creates acidic condensate that can corrode a masonry flue built for oil.

How long does liner installation take?

It depends on the chimney's height, roof access, condition and the type of liner. After the inspection we'll give you an estimated timeline and let you know whether your heat will be off at any point.

Can a liner be installed during the winter?

Yes, when weather allows safe roof access. Your boiler or water heater may need to be off for part of the work, so we plan the timing with you in advance.

Will a new liner stop my chimney from leaking?

Not by itself. Leaks usually come from the crown, flashing or masonry. A cap installed with the liner helps keep rain out of the flue, and we'll point out any other sources of water we see.

Which areas near Mill Basin do you serve?

We serve Mill Basin in ZIP code 11234, along with Marine Park, Bergen Beach, Flatlands, Madison and Sheepshead Bay.

Schedule a chimney or vent inspection

Tell us what you are noticing, whether it is smoke, smells, leaks or a slow dryer. We will inspect, show you photos, and give you a written price before any work begins.

Call (929) 531-5990 Request Service