Skip to content
Brooklyn, NY Brooklyn, NY Mon–Fri: 8 AM–8 PM · Requests accepted 24/7 · (929) 531-5990

Chimney Liner Installation in Gerritsen Beach, Brooklyn

Serving Gerritsen Beach and nearby cities. Tell us about the job and we’ll call you back to confirm the details.

Tell us what’s going on

Prefer to talk? (929) 531-5990

The short answer

A new chimney liner gives exhaust from your boiler, water heater or fireplace a sealed, correctly sized path out of the house. In Gerritsen Beach, the most common reasons for a new liner are oil-to-gas conversions and cracked or missing clay flue tiles in older chimneys.

Many houses in Gerritsen Beach have chimneys that were never built for today's heating equipment. Some have bare masonry flues. Some have clay tiles that cracked after decades of use. Others were built for oil and now vent a gas boiler or water heater. EliteSweep Chimney Services installs chimney liners for homes in Gerritsen Beach (11235), about 2 miles south of our office in Madison. Our certified technicians size each liner to the appliance it serves. A correctly sized liner drafts properly and keeps heat, moisture and combustion gases inside the chimney instead of in your walls.

Why Liners Matter in Gerritsen Beach Homes

The neighborhood is mostly detached and attached houses, many of them older. Their chimneys may serve a boiler, a water heater, a fireplace, or more than one appliance. Over time, mortar joints wear and clay tiles crack. Flues built for one fuel often end up venting another. A liner gives the exhaust a sealed path of the right size from the appliance to the top of the chimney.

Fuel changes are the most common reason we get called. When a New York City building converts its boiler from oil to gas, the chimney has to be evaluated as part of the work, and a new liner is often needed. Gas exhaust produces acidic condensate that can corrode a masonry flue. Without a proper liner, that damage can show up as flaking brick, stained walls, or mortar and tile debris collecting at the base of the chimney.

Signs Your Chimney May Need a New Liner

Not every chimney needs a new liner. These are the conditions that usually lead to one:

  • You are switching from oil to gas, or replacing a boiler or water heater with a unit of a different size
  • An inspection found cracked, shifted or missing clay flue tiles
  • An unlined masonry flue serves a gas or oil appliance
  • Tile pieces, mortar or rust-colored residue are collecting at the chimney base or cleanout
  • Walls next to the chimney show water stains, peeling paint or dampness
  • You notice backdrafting, soot marks or exhaust smells near the appliance
  • You want to use a fireplace again after it has sat idle for years

Liner Options We Install

The right liner depends on the fuel, the appliance and the shape of the existing flue. We will explain why we recommend one type over another for your chimney.

  • Stainless steel liners: the most common choice for gas and oil boilers and water heaters. They come in rigid sections or flexible sections that can follow minor offsets in the flue.
  • Insulated stainless liners: used for wood-burning fireplaces and inserts. Keeping flue gases warm improves draft and reduces creosote buildup.
  • Cast-in-place liners: a poured lining used in some older masonry chimneys where the flue is irregular or the structure needs reinforcement.
  • Clay tile replacement: an option in certain rebuild situations, where the chimney is taken down to the damaged section.

How a Liner Installation Works

Every job starts with an inspection. The NFPA 211 standard calls for chimneys to be inspected once a year. It calls for a Level 2 inspection when the system changes, such as a new appliance or a switch of fuel. That inspection includes a camera scan of the flue, measurements, and a check of the appliance connections. Sometimes a hidden problem can only be reached by opening part of the chimney or a wall. That is a Level 3 inspection, and we will tell you before any opening is made.

Next we size the liner. If a flue is too large for a modern high-efficiency boiler, exhaust can cool and condense before it leaves the chimney. If it is too small, it can restrict draft. We match the diameter to the appliance manufacturer's venting requirements. Then we install the liner from the top down, connect it at the base, and fit a cap at the top. Finally, we test the draft with the appliance running. We walk you through the work and show you photos of the finished liner.

Scheduling Around the Heating Season

New York City's heat season runs from October 1 through May 31. During that time, building owners must keep apartments heated to the city's minimum temperatures. If your house includes a rental unit, or you don't want to be without heat in January, plan liner work for late spring or summer. When a liner is needed in the middle of winter, we work to keep your boiler offline for as little time as possible. Besides Gerritsen Beach, we also serve nearby Sheepshead Bay, Manhattan Beach, Madison, Homecrest and Gravesend.

More services in Gerritsen Beach

Related

What to expect

How a visit goes

  1. We look before we recommend

    We inspect the flue, damper, crown, cap and connections first, then tell you what we found. Recommendations come from what is in your chimney, not from a standard package.

  2. We keep your home clean

    Drop cloths go down before any work starts, and soot and debris are contained and carried out. We leave the room the way we found it.

  3. We explain it in plain English

    You will hear what each problem is, why it matters, and what happens if you wait. If something can safely be left for later, we say so.

FAQ

Common questions

Don’t see your question? Call (929) 531-5990 and we’ll talk it through.

Do I need a new liner if I'm converting my boiler from oil to gas?

Often, yes. In New York City, the chimney has to be evaluated as part of an oil-to-gas conversion. A new liner is frequently needed because gas exhaust produces acidic condensate that can corrode a masonry flue.

Can a liner be installed in a chimney with cracked clay tiles?

In many cases, yes. A stainless steel liner can usually run through the existing flue after loose or broken pieces are cleared. The inspection shows whether the chimney structure itself also needs repair.

Can one chimney vent both my boiler and my water heater?

Sometimes. It depends on the size of the flue, the appliances and their venting requirements. Some homes need separate liners, while others can use a properly sized common connection. We determine this during the inspection.

How long does a chimney liner installation take?

A straightforward stainless steel reline is often finished in a single visit. Cast-in-place liners, masonry repairs or difficult flue offsets take longer. We will give you a time estimate after the inspection.

How often should a lined chimney be inspected?

The NFPA 211 standard calls for chimneys, fireplaces and vents to be inspected once a year, even after a new liner is installed. A yearly check catches problems with caps, connections and buildup early.

Do you install liners outside Gerritsen Beach?

Yes. Our office is in Madison, and we also install liners in Sheepshead Bay, Manhattan Beach, Homecrest, Gravesend and Madison.

Schedule a chimney or vent inspection

Tell us what you are noticing, whether it is smoke, smells, leaks or a slow dryer. We will inspect, show you photos, and give you a written price before any work begins.

Call (929) 531-5990 Request Service